Minwax® Clear Brushing Lacquer

Minwax® Clear Brushing Lacquer

A clear, protective finish for wood and metal that dries to the touch in 30 minutes, ensuring a smooth, dust-free finish. No sanding required between coats. Also available in an aerosol can.

Product Details

Sheens: Gloss, Semi-Gloss, Satin
Application Tool: high quality natural bristle brush
Location: interior wood surfaces
Recoat: after 2 hours
Dry time: dries to the touch in 30 minutes
Cleanup: lacquer thinner
Coverage: 125 sq. ft. per quart
Coats: at least 3
Recommended Uses: woodwork, cabinets, furniture, interior doors, accessories

Directions

For aerosol directions, click here

WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.

  1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter. Note: Do not apply lacquer over polyurethane finishes.
  2. Sand to obtain a smooth, uniform surface. Remove all dust with a cloth dampened with mineral spirits.
  3. Apply Minwax®Wood Finish™ stain or Minwax® Lacquer Sanding Sealer , if desired, following label directions.
  4. Stir Minwax® Clear Brushing Lacquer well before and during use to rotate the product from the bottom to the top of the can. NEVER SHAKE.
  5. Apply a coat of lacquer using a high quality natural bristle brush. On unfinished wood, apply sufficient lacquer to seal open joints, edges and end grain.
  6. Let dry at least two hours, then apply a second coat.
  7. Apply a third coat, repeating the steps above for each coat. Apply a fourth coat, if desired.
  8. After final coat, allow at least 24 hours before normal use.

CLEAN UP: For easy clean-up use lacquer thinner.

COVERAGE: Approximately 125 sq. ft. per quart.

Note: For brush application only. Above dry times and coverage rates are based on good ventilation, temperature of 77° F and 50% relative humidity. Lower temperature, higher humidity, lack of ventilation or application of thick coats will extend dry time. Always test tackiness between coats. Do not recoat if surface is still tacky. Slight ambering may be experienced when lacquer is applied over light-colored stains or wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. Minwax® Clear Brushing Lacquer is not recommended for use on floors. To protect floors, use Minwax® Super Fast-Drying Polyurethane for Floors or Minwax® Water Based Polyurethane for Floors.

Aerosol Directions

WARNING! If you scrape, sand or remove old paint, you may release lead dust. Lead is Toxic. Contact the National Lead Information Hotline at 1-800-424-LEAD or log onto www.epa.gov/lead.

  1. Surface must be dry and free of old finished in poor condition, paint, wax, grease, polish, dirt or other foreign matter. Note: Do not apply lacquer over polyurethane finishes.
  2. Sand the wood to obtain a smooth, uniform surface. Remove all dust with cloth dampened with mineral spirits.
  3. Apply Minwax® Wood Finish™ stain or Minwax® Lacquer Sanding Sealer, if desired, following label directions.
  4. Shake the can of Minwax® Clear Aerosol Lacquer vigorously for two minutes. Shake for 10 seconds occasionally during use.
  5. Protect adjacent areas from overspray. Wet overspray can be removed with lacquer thinner.
  6. Hold can vertically 6-10 inches from surface. Depress button fully and spray using an even, sweeping motion with slightly overlapping strokes. Spray several thin coats at the first spraying. On unfinished wood, apply sufficient material to seal open joins, edges and end-grain.
  7. Recoat after 30 minutes.
  8. Apply at least three coats.
  9. After final coat, allot at least 24 hours before normal use.

Note: Above dry times are based on good ventilation temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Always test tackiness between coats. Do not recoat if surface is still tacky. Always spot test an inconspicuous area to ensure satisfactory results.

Nozzle Care

  1. Immediately after using, turn can upside down and depress nozzle until no liquid comes out.
  2. If nozzle is clogged, pull from can and clean with lacquer thinner- Do NOT stick pins or wires into the can opening.

Clean-Up: For easy clean-up, use lacquer thinner following the manufacturer’s safety instructions.

CAUTION! CONTAINS ACETATES, KETONES AND HYDROCARBON PROPELLANTS. DANGER! EXTREMELY FLAMMABLE. Do not spray near sparks, heat or open flame. Vapors will accumulate readily and may ignite explosively. Keep area ventilated during use and until all vapors are gone. DO NOT SMOKE- Extinguish all flames, pilot lights and heaters. - Turn off stoves, electric tools and appliances, and any other sources of ignition. CONTENTS UNDER PRESSURE. Avoid prolonged exposure to sunlight or heat from radiators, stoves, hot water and other heat sources that may cause bursting. Do not puncture, incinerate, burn or store above 120°F. Do not discard empty can in trash compactor. VAPOR HARMFUL. Use with adequate ventilation. Avoid continuous breathing of vapor and spray mist. To avoid breathing vapors or spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.

Conforms to ASTM D-4236. Contact a physician for more health information.