Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.
STEP 3: APPLY MINWAX® SUPER FAST-DRYING POLYURETHANE FOR FLOORS– Before use, thoroughly stir Minwax Super Fast-Drying Polyurethane for Floors to rotate the product from the bottom to the top of the can. You will not need to stir again if the project will be completed in 1 day.– Apply a thin coat using a lambswool or synthetic-pad applicator, or a natural bristle brush. Maintain a wet edge to avoid lap marks.– Allow the finish to dry 6-8 hours, but less than 10 hours. If this timing is followed, no sanding between coats is needed! But if you have let the finish dry for more than 10 hours, sand the finish lightly with 220-grit sandpaper. Allow 8 hours dry time before you sand.– Apply a second coat following the steps above.If you are applying Super Fast-Drying Polyurethane for Floors to bare wood, apply a third coat, following the steps above. If this is a “screen and recoat”, or if you are applying Super Fast-Drying Polyurethane for Floors over stain, only 2 coats are required.Note: Sanding is not required between coats, but for maximum smoothness, you can choose to sand before the final coat, using 220-grit sandpaper or equivalent. Allow 6-8 hours dry time before you sand. Do not sand if the film is still tacky. The product appears dark in the can, but dries clear. Floor will bear light foot traffic in 24 hours. Avoid heavy traffic, and do not install rugs or clean floors for 7 days. When replacing furniture, do not slide. If Minwax® Sanding Sealer is used prior to Super Fast-Drying Polyurethane for Floors, apply following the label directions. Wait a minimum of 2 hours before sanding, and apply 2 coats of Super Fast-Drying Polyurethane for Floors.
DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations. CAUTIONS: CONTAINS ALIPHATIC HYDROCARBONS. Contents are COMBUSTIBLE. Keep away from heat and open flame. VAPOR HARMFUL. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage. FIRST AID: In case of eye contact, flush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.
SATISFACTION GUARANTEE LIMITED WARRANTY. This warranty is made to you, the product purchaser who owns the property where the product is applied. This warranty is not transferable except that if a contractor purchased and applied the product to the property for you, then the warranty is transferable to you. If this product, when applied and maintained according to product application and maintenance instructions to a properly prepared surface, fails to perform to your complete satisfaction, Minwax shall, upon presentation of proof of purchase, either replace an equivalent quantity of product free of charge or refund the original purchase price. For a replacement or refund please contact customer service at 1-800-523-9299. This warranty shall not apply to any defect, damage, or product failure resulting from improper surface preparation, structural defects, environmental damage, failure of a previous product, deterioration or defect in the underlying substrate, or improper application or maintenance of the product. Your exclusive remedy, and Minwax's sole liability, under this warranty is the replacement of product or refund and does not include labor or costs associated with the application or removal of any product. IN NO EVENT SHALL MINWAX BE LIABLE FOR ANY TYPE OF INCIDENTAL, CONSEQUENTIAL, SPECIAL, EXEMPLARY, PUNITIVE, OR INDIRECT DAMAGES WHETHER OR NOT PURCHASER IS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL HAVE THE SAME DURATION AS THE ABOVE EXPRESS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts or limitations on incidental or consequential damages, so portions of the limitations above might not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from state to state.